Made of die-cast metal alloy, this die holder features screws for precise centering of dies and a hammered gray lacquer finish. Available in two models: code U06180045 for dies from M3 to M9, with a capacity of 220 mm, and code U06180046 for dies from M10 to M12, with a capacity of 325 mm.

Compliant with DIN 1814, this manual tap wrench features a removable operating shaft and a non-slip knurled end. The body is made of aluminum with steel jaws. Available in three models: code U06180041 for capacity M1÷M10, length 175 mm; code U06180042 for capacity M3.5÷M12, length 277 mm; and code U06180043 for capacity M5÷M20, length 375 mm.

Long two-jaw model, with ratchet that can work clockwise, anticlockwise or in a fixed position. Available in two versions: code U06180101 with female square drive from 2.6÷5.5 mm and length 255 mm; code U06180102 with female square drive from 4.6÷8 mm and length 315 mm.

Short two-jaw model with right-hand, left-hand or fixed position ratchet. Available in two versions: code U06180001 with 2.6÷5.5 mm female square drive and 85 mm length; code U06180002 with 4.6÷8 mm female square drive and 110 mm length.

Made from HSS steel, these carbide taps come in sets of 3 (roughing, intermediate and finishing) with square shank.

ISO metric right-hand pitch, made of HSS chrome vanadium high speed steel treated to 62/64 HRc (234 daN/mm²). Equipped with a conical adjustment screw for perfect adjustment of the thread diameter.

Series of spatulas with rigid stainless steel blade, including straight (32, 50) and bent (32P) models. Equipped with ergonomic bi-material non-slip handle and rear steel tang.

Spatulas with rigid stainless steel blade, available in straight (32, 50) and bent (32P) models. Equipped with an ergonomic, non-slip bi-material handle and a steel rear tang.

Spatulas with flexible stainless steel blade, clean shiny finish. Equipped with ergonomic bimaterial non-slip handle.

Spatulas with flexible stainless steel blade, clean shiny finish. Equipped with ergonomic bimaterial non-slip handle.

Model with material dispensing stop device and aluminium body.

The 490 nut splitter cuts off stuck nuts without damaging the screws. It is made of carbon steel and Chrome Vanadium, with a chrome and burnished finish, available in different sizes for various nut sizes.

The 468 C internal expansion extractors are designed for use with the 468 D holder or the 468 E impact extractor. Made of special high-alloy Chrome Vanadium steel and with a burnished finish, they offer strength and durability for precise and reliable extraction operations.

The 458 Series Conical Extractors are designed to remove broken screws or studs that do not provide gripping ability. They are made of special Chrome Vanadium alloy steel, with a satin and burnished finish for greater durability and strength.

Replacement screw 454 B for 454 series extractors. Available in various sizes for models 0 to 6.

454 A arm change for 454 series extractors. Available in different sizes for models 0 to 6.

Model with sliding arms, Carbon steel screw, Chrome Vanadium steel body, chromed and burnished finish. Capacity from 65 to 340 mm, power from 1.5 to 5 tons.

Spare part for 451 NT extractors, available in two codes: U04510007Q (n° 1) and U04510008Q (n° 2).

Self-tightening three-arm extractors with safety pin, also usable with two arms. They are equipped with a carbon steel operating screw (M16x2) with 18 mm hexagon. The extraction capacity varies between 23÷55 mm (model NT1) and 30÷55 mm (model NT2) in combination with the 468 E2 impact mass. Available codes: U04510005 (NT1 - 23÷140 mm), U04510006 (NT2 - 30÷190 mm).